Redundancy Reduction for Sensor Deployment in Prosthetic Socket: A Case Study.

The irregular pressure exerted by a prosthetic socket over the residual limb is one of the major factors that cause the discomfort of amputees using artificial limbs. By deploying the wearable sensors inside the socket, the interfacial pressure distribution can be studied to find the active regions and rectify the socket design. In this case study, a clustering-based analysis method is presented to evaluate the density and layout of these sensors, which aims to reduce the local redundancy of the sensor deployment. In particular, a Self-Organizing Map (SOM) and K-means algorithm are employed to find the clustering results of the sensor data, taking the pressure measurement of a predefined sensor placement as the input. Then, one suitable clustering result is selected to detect the layout redundancy from the input area. After that, the Pearson correlation coefficient (PCC) is used as a similarity metric to guide the removal of redundant sensors and generate a new sparser layout. The Jenson-Shannon Divergence (JSD) and the mean pressure are applied as posterior validation metrics that compare the pressure features before and after sensor removal. A case study of a clinical trial with two sensor strips is used to prove the utility of the clustering-based analysis method. The sensors on the posterior and medial regions are suggested to be reduced, and the main pressure features are kept. The proposed method can help sensor designers optimize sensor configurations for intra-socket measurements and thus assist the prosthetists in improving the socket fitting.

A Scoping Review of Pressure Measurements in Prosthetic Sockets of Transfemoral Amputees during Ambulation: Key Considerations for Sensor Design.

Sensor systems to measure pressure at the stump-socket interface of transfemoral amputees are receiving increasing attention as they allow monitoring to evaluate patient comfort and socket fit. However, transfemoral amputees have many unique characteristics, and it is unclear whether existing research on sensor systems take these sufficiently into account or if it is conducted in ways likely to lead to substantial breakthroughs. This investigation addresses these concerns through a scoping review to profile research regarding sensors in transfemoral sockets with the aim of advancing and improving prosthetic socket design, comfort and fit for transfemoral amputees. Publications found from searching four scientific databases were screened, and 17 papers were found relating to the aim of this review. After quality assessment, 12 articles were finally selected for analysis. Three main contributions are provided: a de facto methodology for experimental studies on the implications of intra-socket pressure sensor use for transfemoral amputees; the suggestion that associated sensor design breakthroughs would be more likely if pressure sensors were developed in close combination with other types of sensors and in closer cooperation with those in possession of an in-depth domain knowledge in prosthetics; and that this research would be facilitated by increased interdisciplinary cooperation and open research data generation.

Reconstruction of the lower limb bones from digitised anatomical landmarks using statistical shape modelling.

BACKGROUND: Bone shapes strongly influence force and moment predictions of kinematic and musculoskeletal models used in motion analysis. The precise determination of joint reference frames is essential for accurate predictions. Since clinical motion analysis typically does not include medical imaging, from which bone shapes may be obtained, scaling methods using reference subjects to create subject-specific bone geometries are widely used. RESEARCH QUESTION: This study investigated if lower limb bone shape predictions from skin-based measurements, utilising an underlying statistical shape model (SSM) that corrects for soft tissue artefacts in digitisation, can be used to improve conventional linear scaling methods of bone geometries. METHODS: SSMs created from 35 healthy adult femurs and tibiae/fibulae were used to reconstruct bone shapes by minimising the distance between anatomical landmarks on the models and those digitised in the motion laboratory or on medical images. Soft tissue artefacts were quantified from magnetic resonance images and then used to predict distances between landmarks digitised on the skin surface and bone. Reconstruction results were compared to linearly scaled models by measuring root mean squared distances to segmented surfaces, calculating differences of commonly used anatomical measures and the errors in the prediction of the hip joint centre. RESULTS: SSM reconstructed surface predictions from varying landmark sets from skin and bone landmarks were more accurate compared to linear scaling methods (2.60-2.95 mm vs. 3.66-3.87 mm median error; p < 0.05). No significant differences were found between SSM reconstructions from bony landmarks and SSM reconstructions from digitised landmarks obtained in the motion lab and therefore reconstructions using skin landmarks are as accurate as reconstructions from landmarks obtained from medical images. SIGNIFICANCE: These results indicate that SSM reconstructions can be used to increase the accuracy in obtaining bone shapes from surface digitised experimental data acquired in motion lab environments.